M18-Style Ten-Cell Housing and Bidirectional USB-C PCB Kit
Key Features
- Aftermarket DIY housing and PCB kit for the pictured Milwaukee M18-style interface, designed to hold ten 18650 power cells. Cells are not included.
- The original wiring diagram depicts five series-connected groups of two parallel cells: 5S2P, ten cells total.
- The supplier lists bidirectional USB-C profiles of 5V/3A, 9V/3A, 12V/3A, 15V/3A, and 20V/2.25A, up to 45W with a compatible connected device.
- The PCB provides supplier-listed overcharge, overdischarge, overcurrent, and individual cell-group voltage monitoring, with a stated 20A maximum continuous discharge rating.
- Includes the photographed empty case, cell holder, PCB, contact strips, indicator parts, and hardware. Assembly skills, cells, tools, cables, and chargers are required separately.
Specifications
A DIY component kit, not an assembled battery or an original-equipment product. The complete original parts, PCB, dimensions, wiring reference, and USB-C demonstrations remain. The housing figure lists 11.5 cm length and 8 cm width, with two pictured height annotations of 7.3 cm and 4.9 cm; the PCB figure lists approximately 8.4 x 3 cm. Dimensions are reference measurements: the original image states a 0-2 cm allowance while the supplier prose states +/-3 cm, so no tighter dimensional tolerance is established. USB-C power, current limits, protocols, and protection behavior are supplier specifications, not independent test results. PCB color, component count or placement, and contact-strip appearance may change between production batches; the supplier states that the intended fit, function, and performance are maintained. Compare the actual housing and battery interface before ordering.
USB-C Charging and Power Output
The supplier lists AFC, FCP, PD2.0, PD3.0, and PD3.1 charging support. Output protocol references include PD2.0, PD3.0, PD3.1, QC2.0, QC3.0, QC3+, FCP, AFC, and Apple fast charging. A protocol name does not establish additional voltage profiles or power above the listed 45W maximum. Actual charging current depends on the charger, cable, cells, and operating conditions. Press the indicator button to display the voltage-based charge level.
Do not charge and discharge through USB-C at the same time. The supplier warns that simultaneous operation can damage or burn out the PCB. If the assembled pack has no output on first power-up, the source calls for activation with an appropriate dedicated battery charger. Subsequent normal USB-C charging can use a compatible phone charger; a dedicated charger is not required for that routine USB-C function.
Assembly Requirements
This kit requires experience assembling lithium-ion battery packs. Supply ten suitable 18650 power cells, a spot welder, soldering iron, multimeter, and a matched charger. The supplier recommends new high-discharge cells rated above 15C; this is a cell C-rate recommendation, not a 15A rating. Verify that every cell is suitable for the intended pack and load.
Measure and equalize all cell voltages before connecting or welding the PCB. When repairing a pack, check each cell and bring suitable cells to the same voltage before assembly. Never reverse polarity. Insulate the PCB from direct contact with the cells and secure all parts. Do not touch onboard components with loose pins or a soldering iron. Protect the assembly from static discharge, moisture, and water.
Source Terminal References
The supplier identifies charging negative as P-/PC- and charging positive as PC+/CH+. It identifies load negative as LOAD-/PD-/P- and load positive as LOAD+/P+/B+. These are the source's alternative terminal labels, not proof that every label is printed on this board revision. Identify the actual terminals and polarity on the supplied board before making connections. The complete original wiring figure is retained as a reference; it shows ten cells arranged 5S2P, rather than a ten-series pack.
Protection and Fault Indications
- Low charge: LED1 flashes red.
- An open or shorted NTC temperature-sensor circuit blocks charging.
- A broken connection can lock the protection circuit; the supplier states charging and discharging resume after the wiring is repaired.
- Charging stops when a monitored cell group reaches its overcharge threshold; no unlisted threshold is assumed.
- USB-C overcurrent in a 9V, 12V, 15V, or 20V mode falls back to 5V. Remove the load to reset an overcurrent condition in 5V mode.
Phone, charger, cables, cells, and finished battery packs shown in demonstrations are operating references and are not supplied with the empty kit.
Original Ten-Cell USB-C Housing Kit